Based loosely on rings from the Bronze Age Andronovo culture of Central Asia. This one is made of 3/32-inch brass rod, and has one less loop around the finger than the originals. It's made by repeated annealing, bending with tweezers and hammering to make the curlicues tight, then wrapping around a 3/4-inch wooden dowel.
I've recently discovered that some yellow brass cracks easily when forged. The rod for this project came from Ace Hardware. I don't know the alloy, but at least I know whatever it is they carry forges well.
I somewhat overestimated the length required, so I tightened the
wrap and took up the slack to keep the curlicues in line with each other by rolling
them up more. Unfortunately, because they are slightly oblong, curling
them a little too much causes them to stick out more and rub against my joints.
Polishing was a pain; I used both Brasso and fine
polishing paper to get the black scale off, and as you can see, there
was still some inside the curlicues that was out of reach. To prevent
tarnish, I sprayed the ring with automotive lacquer. I'm not yet sure
whether this will work. I do know that it replaces the nice metallic
shine with a slightly plasticky one and also causes the metal to feel
squeaky when being worn.
Showing posts with label jewelry. Show all posts
Showing posts with label jewelry. Show all posts
Tuesday, April 5, 2022
Tuesday, June 25, 2019
Fibula 2
Here we go again:
This one is made from 1.5mm steel rod (a hair less than 1/16-inch). I think this is a bit too thin, and might not stand up to the strain of fastening a heavy cloak. But it works much, much better than the 1/8-inch in any case. I might consider using a thickness up to 1/12-inch or so.
The use of only a single brass bead is intentional, as I wanted to keep the amount of metal to a minimum. The round copper-plated beads on the first attempt already had 1/8-inch holes, so they were easy to use as filler. However, for this pin, that wasn't necessary, since it was easier to drill out enough bone beads to fill out the bow when I only had to increase the hole diameter from about 1mm to 1.5mm.
And one more time:
Of course it turned out wonky due to the metal bending too much where the large round bead should be, forcing it over to one side. I also made the pin too short, which didn't help. Due to the wonky bead and too-acute bend in the bow, I think this attempt looks much less elegant than it could. I might remake it someday.
A few notes: Some of the bone beads - which, according to the package, come from the "Cherished Collection by Nicole" (um, sure) - had tiny seed beads jammed in the stringing holes which had to be pushed out before the bone beads were useable.
Also, the steel, which comes from the spine of a marker flag, is apparently high-carbon. Between the second and third successful fibulae, I accidentally quench-hardened another pin while forming the coil, which was the first time I'd ever successfully quench-hardened anything, causing the coil to snap like dry spaghetti.
This one is made from 1.5mm steel rod (a hair less than 1/16-inch). I think this is a bit too thin, and might not stand up to the strain of fastening a heavy cloak. But it works much, much better than the 1/8-inch in any case. I might consider using a thickness up to 1/12-inch or so.
The use of only a single brass bead is intentional, as I wanted to keep the amount of metal to a minimum. The round copper-plated beads on the first attempt already had 1/8-inch holes, so they were easy to use as filler. However, for this pin, that wasn't necessary, since it was easier to drill out enough bone beads to fill out the bow when I only had to increase the hole diameter from about 1mm to 1.5mm.
And one more time:
Of course it turned out wonky due to the metal bending too much where the large round bead should be, forcing it over to one side. I also made the pin too short, which didn't help. Due to the wonky bead and too-acute bend in the bow, I think this attempt looks much less elegant than it could. I might remake it someday.
A few notes: Some of the bone beads - which, according to the package, come from the "Cherished Collection by Nicole" (um, sure) - had tiny seed beads jammed in the stringing holes which had to be pushed out before the bone beads were useable.
Also, the steel, which comes from the spine of a marker flag, is apparently high-carbon. Between the second and third successful fibulae, I accidentally quench-hardened another pin while forming the coil, which was the first time I'd ever successfully quench-hardened anything, causing the coil to snap like dry spaghetti.
Sunday, June 23, 2019
Fibula
Steel rod with bone and brass beads.
Lessons learned: For this purpose, 1/8-inch steel is much too heavy. Shaping it required a lot of annealing and forging. The rod is also too stiff, making it difficult to clasp and unclasp, and pressing on the bow of the fibula in the process puts a lot of pressure that I fear will eventually crack the bone beads, even though they're not packed together. And, of course, I wasted a lot of time enlarging the stringing holes on each bead (except the small smooth brass ones).
The bone beads are from an inexpensive packet I got at A.C. Moore. The brass ones are from Crazy Crow. Actually, the smooth brass beads are copper-plated.
I would like to try again with a thinner steel, in 1/12 or even 1/16-inch if I can find it. I also wanted to incorporate fewer metal beads and some animal horn ones.
Lessons learned: For this purpose, 1/8-inch steel is much too heavy. Shaping it required a lot of annealing and forging. The rod is also too stiff, making it difficult to clasp and unclasp, and pressing on the bow of the fibula in the process puts a lot of pressure that I fear will eventually crack the bone beads, even though they're not packed together. And, of course, I wasted a lot of time enlarging the stringing holes on each bead (except the small smooth brass ones).
The bone beads are from an inexpensive packet I got at A.C. Moore. The brass ones are from Crazy Crow. Actually, the smooth brass beads are copper-plated.
I would like to try again with a thinner steel, in 1/12 or even 1/16-inch if I can find it. I also wanted to incorporate fewer metal beads and some animal horn ones.
Tuesday, September 4, 2018
Peace, love and revolution
I made this rosette yesterday according to the instructions in this demo. I'm not sure why mine turned out so messy; it may just be lack of practice, or it may be the fact that it's a very narrow (5/8-inch) ribbon.
The pin is heavy-gauge sheet brass, etched as usual and painted with Testors enamel. As I didn't have an extremely fine brush, the enamel tended to slop out of the recesses, but with the brass well burnished, I was able to scrape off the excess with a needle when it was half-dried.
The pin has not yet been lacquered. In my experience, spray lacquers invariably take away some of the metallic shine, but the alternative is to let the metal tarnish. Lacquer will at least keep it bright and glossy.
The rosette is sewn to a circle of blue garment leather with a hole poked through the middle, and I soldered a tie tack back to the face, sanding the back of the face and the top of the tack to make sure the solder would adhere. The solder this time was a low-temperature paste, and I slid a pair of heavy brass beads around the actual pin to act as a heat sink, all in an effort to prevent the pin from annealing and becoming too bendable to poke through fabric. I'm not sure how well I succeeded (the beads were glowing orange by the time the solder melted), but it seems to work okay. All of this, of course, was done before the final polish, burnishing and painting of the face.
The pin is heavy-gauge sheet brass, etched as usual and painted with Testors enamel. As I didn't have an extremely fine brush, the enamel tended to slop out of the recesses, but with the brass well burnished, I was able to scrape off the excess with a needle when it was half-dried.
The pin has not yet been lacquered. In my experience, spray lacquers invariably take away some of the metallic shine, but the alternative is to let the metal tarnish. Lacquer will at least keep it bright and glossy.
The rosette is sewn to a circle of blue garment leather with a hole poked through the middle, and I soldered a tie tack back to the face, sanding the back of the face and the top of the tack to make sure the solder would adhere. The solder this time was a low-temperature paste, and I slid a pair of heavy brass beads around the actual pin to act as a heat sink, all in an effort to prevent the pin from annealing and becoming too bendable to poke through fabric. I'm not sure how well I succeeded (the beads were glowing orange by the time the solder melted), but it seems to work okay. All of this, of course, was done before the final polish, burnishing and painting of the face.
Saturday, July 7, 2018
A pewter lapel pin II
A remake of a pin I created last December. Just last week, I came across several pages which cleared up the real-world identity of this emblem and provided some better views of how it should be proportioned.
In comparing my first pin and subsequently the one in the film's promotional photos with the actual Soviet ones, I noticed several discrepancies which, unlike the frontwise proportions, can't be put down to the odd camera angle. First, the one in the film clearly has the hammer's handle protruding out the top of its head; second, the angled ends of the wrench's jaws are pointing the wrong way; and third, it appears to be much too thick - likely cast, while the originals look to me to have been stamped.
Another source of cognitive dissonance is the fact that in the movie, Courtenay wears the emblem in what is supposed to be 1913, forty years before it seems to have been made part of the official Soviet railway uniform, and five years before the Bolsheviks even took power in Russia. In the book, Pasha Antipov's father was a railway worker, and I take it that the same is supposed to be true of Pasha in the film, although I can't recall whether he mentions it (in the book he's a schoolteacher). The cap he wears strongly resembles a Soviet railway staffer's cap from the 1955-63 period, shortly before the film was made, but it's missing its chin cord and has a number of other minor differences from those shown at Under the Red Star.
I have yet to discover whether a version of the hammer and monkey wrench symbol was used prior to the Revolution. But my theory is that the film's costume department simply produced a crude replica of a near-contemporary Soviet railway badge and cap.
In creating a new version of the pin, I incorporated the oddities of the film version while correcting the mistakes of my first attempt and being careful to avoid the mass of flash that my first pin had around the hammer's head. Otherwise, the process was almost exactly the same, except that I sunk a piece of heavy paper clip into the pewter running down the hammer's handle to strengthen it.
I also let the plaster sit longer before prying the wax out, in the hopes of not damaging the plaster. In hindsight, I should've let it sit until it was cold, because the heat of the plaster as it cured softened the wax and made it more difficult to extract.
Like the first time around, I had to do a lot of cleanup with files, and there's still some more left. The bevels on the wrench jaws should be at a shallower angle and some of the meat between the jaws still needs to be ground out. I had no hope of recreating the threading there, but I don't think the movie version did either.
I managed one other improvement this time around: Rather than polishing with a wire Dremel brush, I rubbed the surfaces with a fine file and then burnished them with the round back of a steel nail scissor handle. Since the solder/pewter is much softer than steel, this resulted in a near mirror finish.
In comparing my first pin and subsequently the one in the film's promotional photos with the actual Soviet ones, I noticed several discrepancies which, unlike the frontwise proportions, can't be put down to the odd camera angle. First, the one in the film clearly has the hammer's handle protruding out the top of its head; second, the angled ends of the wrench's jaws are pointing the wrong way; and third, it appears to be much too thick - likely cast, while the originals look to me to have been stamped.
Another source of cognitive dissonance is the fact that in the movie, Courtenay wears the emblem in what is supposed to be 1913, forty years before it seems to have been made part of the official Soviet railway uniform, and five years before the Bolsheviks even took power in Russia. In the book, Pasha Antipov's father was a railway worker, and I take it that the same is supposed to be true of Pasha in the film, although I can't recall whether he mentions it (in the book he's a schoolteacher). The cap he wears strongly resembles a Soviet railway staffer's cap from the 1955-63 period, shortly before the film was made, but it's missing its chin cord and has a number of other minor differences from those shown at Under the Red Star.
I have yet to discover whether a version of the hammer and monkey wrench symbol was used prior to the Revolution. But my theory is that the film's costume department simply produced a crude replica of a near-contemporary Soviet railway badge and cap.
In creating a new version of the pin, I incorporated the oddities of the film version while correcting the mistakes of my first attempt and being careful to avoid the mass of flash that my first pin had around the hammer's head. Otherwise, the process was almost exactly the same, except that I sunk a piece of heavy paper clip into the pewter running down the hammer's handle to strengthen it.
I also let the plaster sit longer before prying the wax out, in the hopes of not damaging the plaster. In hindsight, I should've let it sit until it was cold, because the heat of the plaster as it cured softened the wax and made it more difficult to extract.
Like the first time around, I had to do a lot of cleanup with files, and there's still some more left. The bevels on the wrench jaws should be at a shallower angle and some of the meat between the jaws still needs to be ground out. I had no hope of recreating the threading there, but I don't think the movie version did either.
I managed one other improvement this time around: Rather than polishing with a wire Dremel brush, I rubbed the surfaces with a fine file and then burnished them with the round back of a steel nail scissor handle. Since the solder/pewter is much softer than steel, this resulted in a near mirror finish.
Wednesday, December 20, 2017
A pewter lapel pin
I've been mulling over this as part of a Halloween costume since I finished reading Doctor Zhivago a few months ago. Early on in the 1965 film version, Pasha Antipov (Tom Courtenay) wears an unusual pin on his hat, a crossed hammer and monkey wrench, during his not-Bolshevik labor movement activities. I've so far failed to figure out what organization this emblem belonged to, if indeed it was a real emblem (it's been so long since I've seen the film that I can't remember if it's explained onscreen), but a closeup publicity photo (inset) gave me a degree of detail which I attempted to copy.
I made the copy in wax, piecing it together and trying to keep its profile in proportion to the film version, but deeper from front to back for strength, with no undercuts. Then I dabbed thin plaster into its front face and placed it face-down in the cutoff lower quarter of a plastic cup full of plaster to make an open-topped mold. Once the wax was hard but still felt a bit damp, I peeled the wax out. Two days later, I put the mold in a low toaster oven for an hour and a half to try to drive out any remaining moisture, and three days after that I figured it was time for casting.
I intended to use lead-free pewter, of which I had a small amount left over from making an akinakes chape for Marathon 2011. But I couldn't find it in my house, even though I swear I saw it not long ago. With no other option, I picked up some low-temperature solder at a hardware store - this is a lead-free, silver-bearing alloy, but it still had a low melting point of 430 degrees Fahrenheit. It wouldn't surprise me if the one used in filming was a cheap white metal as well, though it could have been brass - it looks silvery to me in color screenshots, but as I well know, photography doesn't always accurately reflect actual colors.
Next I made a small pot for the actual melting and pouring of metal. This is a 1-1/2 inch copper end cap, annealed and with a spout beaten in by means of placing the cap partly over a cross-peen hammer and smashing it into a block of wood. Then I drilled a hole in the back and in the end of a piece of thick brass strip, and attached them with a copper rivet peened on the outside, over an anvil horn at Bucks' metal room. Since the brass handle still conducts heat, it has to be handled with thick insulating gloves or a pair of pliers. The pot may be heated on a stovetop or over a gas flame, which is what I did here, balancing it between two firebricks.
On my first attempt, I put way too much solder in the mold, giving it a large blobby back. Attempting to scrape off the excess damaged the rapidly-cooling casting. The mold broke on the first casting - perhaps it was still too damp; my foundry professor tells me that investment for jewelry is usually baked for around a whole day. Or perhaps it couldn't withstand the heat even when dry, or my first attempt at divestment was what cracked it. In any case, it was clear that I needed to try again, so I shoved the broken casting back in, held the mold together by wedging it between a pair of firebricks, and remelted with the gas torch.
Possibly as a result of the damaged mold, there's a lot of flashing below the hammer's head, which, as you can see, detracts from the striking appearance of the crossed tools. I could probably file it out, but it would take a long time, and I think that the hammer's skinny neck, supporting the relatively massive head, would be prone to breaking without the flashing to strengthen it. Also, obviously the threaded middle of the wrench isn't as finely threaded or clear in detail as in the film version - the former being the fault of my original wax (it's not easy to cram such fine detail into a wax model) and the latter either because of me failing to work the plaster between the grooves as thoroughly as necessary or because the solder failed to flow into every crevice.
The proportions are slightly off, but I think adequate for a homemade costume - of course if this were professional work, then I would want it to be truer to the film version. The apparent bend of the hammer's neck over the wrench isn't nearly as noticeable in person; I think it may be largely a result of the lighting here. White metal is difficult to photograph under bright sunlight, as it glares a lot, obscuring details, so I waited until I had time to take photos when it was cloudy out. The pin was actually finished last Friday.
With the poured solder sitting in the mold, I blasted the torch over it to make sure it was still liquid, then put a common jewelry pin in the back and tried to drag some solder on top of it with the tip of a piece of thin steel rod. As a result, the back is pretty rough in texture. It's probably not a very secure attachment, but as the uses this pin is going to be put through are not high-stress, it should be good enough.
I tried to clean up some of the flashing and smooth the surfaces with a fine file, then buffed the entire front with a carbon steel Dremel brush.
I made the copy in wax, piecing it together and trying to keep its profile in proportion to the film version, but deeper from front to back for strength, with no undercuts. Then I dabbed thin plaster into its front face and placed it face-down in the cutoff lower quarter of a plastic cup full of plaster to make an open-topped mold. Once the wax was hard but still felt a bit damp, I peeled the wax out. Two days later, I put the mold in a low toaster oven for an hour and a half to try to drive out any remaining moisture, and three days after that I figured it was time for casting.
I intended to use lead-free pewter, of which I had a small amount left over from making an akinakes chape for Marathon 2011. But I couldn't find it in my house, even though I swear I saw it not long ago. With no other option, I picked up some low-temperature solder at a hardware store - this is a lead-free, silver-bearing alloy, but it still had a low melting point of 430 degrees Fahrenheit. It wouldn't surprise me if the one used in filming was a cheap white metal as well, though it could have been brass - it looks silvery to me in color screenshots, but as I well know, photography doesn't always accurately reflect actual colors.
Next I made a small pot for the actual melting and pouring of metal. This is a 1-1/2 inch copper end cap, annealed and with a spout beaten in by means of placing the cap partly over a cross-peen hammer and smashing it into a block of wood. Then I drilled a hole in the back and in the end of a piece of thick brass strip, and attached them with a copper rivet peened on the outside, over an anvil horn at Bucks' metal room. Since the brass handle still conducts heat, it has to be handled with thick insulating gloves or a pair of pliers. The pot may be heated on a stovetop or over a gas flame, which is what I did here, balancing it between two firebricks.
On my first attempt, I put way too much solder in the mold, giving it a large blobby back. Attempting to scrape off the excess damaged the rapidly-cooling casting. The mold broke on the first casting - perhaps it was still too damp; my foundry professor tells me that investment for jewelry is usually baked for around a whole day. Or perhaps it couldn't withstand the heat even when dry, or my first attempt at divestment was what cracked it. In any case, it was clear that I needed to try again, so I shoved the broken casting back in, held the mold together by wedging it between a pair of firebricks, and remelted with the gas torch.
Possibly as a result of the damaged mold, there's a lot of flashing below the hammer's head, which, as you can see, detracts from the striking appearance of the crossed tools. I could probably file it out, but it would take a long time, and I think that the hammer's skinny neck, supporting the relatively massive head, would be prone to breaking without the flashing to strengthen it. Also, obviously the threaded middle of the wrench isn't as finely threaded or clear in detail as in the film version - the former being the fault of my original wax (it's not easy to cram such fine detail into a wax model) and the latter either because of me failing to work the plaster between the grooves as thoroughly as necessary or because the solder failed to flow into every crevice.
The proportions are slightly off, but I think adequate for a homemade costume - of course if this were professional work, then I would want it to be truer to the film version. The apparent bend of the hammer's neck over the wrench isn't nearly as noticeable in person; I think it may be largely a result of the lighting here. White metal is difficult to photograph under bright sunlight, as it glares a lot, obscuring details, so I waited until I had time to take photos when it was cloudy out. The pin was actually finished last Friday.
With the poured solder sitting in the mold, I blasted the torch over it to make sure it was still liquid, then put a common jewelry pin in the back and tried to drag some solder on top of it with the tip of a piece of thin steel rod. As a result, the back is pretty rough in texture. It's probably not a very secure attachment, but as the uses this pin is going to be put through are not high-stress, it should be good enough.
I tried to clean up some of the flashing and smooth the surfaces with a fine file, then buffed the entire front with a carbon steel Dremel brush.
Tuesday, May 9, 2017
Peace, man
I dished this 14ga. brass circle several years ago and never decided what to do with it. Last week, the idea hit me.
The front is etched with ferric chloride (a full hour this time) and patinated with some other kind of ferric compound, probably nitrate.
The back has a one-piece, fibula-style pin, secured with plenty of silver solder. The back and front are finished with a polyurethane varnish to try and preserve the burnished finish for a while.
Since my casual jacket right now is an old surplus jacket (a Swedish M59, to be specific) I figured some peacenik regalia would balance it out a bit.
The front is etched with ferric chloride (a full hour this time) and patinated with some other kind of ferric compound, probably nitrate.
The back has a one-piece, fibula-style pin, secured with plenty of silver solder. The back and front are finished with a polyurethane varnish to try and preserve the burnished finish for a while.
Since my casual jacket right now is an old surplus jacket (a Swedish M59, to be specific) I figured some peacenik regalia would balance it out a bit.
Monday, June 15, 2015
An etched brass medallion
This is what my mom requested for her birthday this year. It's a circle of 16-gauge brass. I scaled down and printed this design, stuck it on with a gluestick, then incised the lines lightly through the paper into the metal with an art knife. After washing the paper and glue off, I used the incisions as guides for a permanent marker mask, sealed off the edges and back with wax, and dropped it into a ferric chloride bath for about 45 minutes.
On the back, the loop (a simple 1/16-inch rod) is secured with what I thought were very small beads of silver solder but which turned out to be more than enough once it was well melted.
I intended to give it a dark patina and brush back the raised knotwork, but none of my experiments with household chemicals worked. Liver of sulfur would've been ideal if I could get any. As it was, Mom said she preferred it with a bright burnished finish. Unfortunately, the texture of the spray lacquer reduced the glossiness; it would probably have been better-off with a painted lacquer instead.
The medallion is worn on a simple brass chain with a silver lobster claw closure.
On the back, the loop (a simple 1/16-inch rod) is secured with what I thought were very small beads of silver solder but which turned out to be more than enough once it was well melted.
I intended to give it a dark patina and brush back the raised knotwork, but none of my experiments with household chemicals worked. Liver of sulfur would've been ideal if I could get any. As it was, Mom said she preferred it with a bright burnished finish. Unfortunately, the texture of the spray lacquer reduced the glossiness; it would probably have been better-off with a painted lacquer instead.
The medallion is worn on a simple brass chain with a silver lobster claw closure.
Subscribe to:
Posts (Atom)




